When the furniture gets old it takes a tiring look. Do you want to refinish them all? Learn the simple rules of how to Refinish a dining room table. We know that a carpenter is the only person who can refine a table. But with a little effort you can figure out how to get it done.
This work does not require some technical equipment. It does not require special tools to refinish. It can be done with some common materials.
Chemical things are needed for this work. Self-protection is the most important thing in life. So it should never be ignored. Use gloves and goggles to protect against allergic reactions to these chemicals. Then place it in a wide ventilated area. A table covered with a high-gloss finish enhances the beauty of the wood. Remember to remove the finish from the surface so that the wood is not damaged in any way. Learn how to rearrange the table after protecting the finish so that it lasts for the next few years.
Below is a list of everything you need to know How to Refinish a Dining Room Table
- Putty knife
- Oil-based stains
- Oil-based polyurethane or tung oil
- 100-, 150- and 220-grit sandpaper
- Steel wool
- Cleaning spray
- Disposable stain brush
- Cotton rags
- Flower sleeve shirt
- Oil stains
- A block or mechanical sander
- Paper towel
- Spectacles for safety
- Rubber gloves for safety
Understand What You are Working on:
Pay attention to the detailed level of the table before you start. The table can be tiring so you have to work carefully. You need to be sure what kind of wood is used in this table.
Clean The Surface:
Clean, clean, clean. First, you need to remove the dirt and oil from the table. This requires mild soap and water. Here you can use your general cleaning supplies. If the table is in very bad condition, it can be torn if it is previously painted or varnished.
If you want to know how to refinish a dining room table then you need to strip the surface perfectly. The table may be painted or varnished, then you need to tear off that surface. Doing this will allow you to clean the table deeply.
Different types of chemical stripping are available at local home improvement stores. You can use non-allergic stripping chemicals for this purpose. It’s up to you which one to use. Spray the stripper chemical well over the entire surface of the table. Wear chemical-resistant gloves, long sleeve shirts and eye protection goggles Carefully remove all stains and old paint from the surface.
Be especially careful about cutting wood. Work in areas where ventilation is very good. Then clean the surface with a putty knife and peel off. It depends on the thickness of the paint how many stripping coats are required. The previous finish can penetrate the fine cracks of the wood so the stripper may need a second or third coat.
Clean With Mineral Spirits
Finish the stripping and let the surface dry. Clean the surface with mind to get the spirits. Now wipe the surface with a clean cloth dipped in spirit. Repeat this process if you are not sure about cleaning. You have created a clean surface for proper sanding.
Stain The Surface
Keep in mind that the more marks you put on the surface, the darker the final color of the wood will be. So, apply some amount in some time so that it can be easily deleted. Carefully remove all sand dust with a fabric.
Sand the table after the wood grain to soften the surface to remove the stained finish. If you choose to use an orbital or belt sander, be very careful not to measure the surface. Do most of the primary sanding with 100-grit sandpaper, then step up to 150-grit and make a final pass with 220-grit to soften the grain. Finish a smoothness that makes you very happy.
You will make the surface very smooth and clean, the next step is to apply the mark. Apply the mark with a disposable brush next to the natural grain of wood. Apply the mark liberally, let it absorb for a few minutes, then wipe off the raise mark with a soft cotton rag. Rub the mark into the fine cracked wood.
Apply The Finish
Wait 2 hours after the final coating of the stain is completely to remove. Apply polyurethane or Tung oil after the table is well dried. Leave the table for at least 12 to 13 hours after staining.
Cover the table with this chemical at least two to three times. The table should be left to dry for at least 24 hours. Then you can use it again. It stays in good condition even after overuse. You can use Citritrip as an alternative. After that the table should be wrapped in plastic wrap.
Can You Restore a Table Without Sanding?
If your table is in good agreement there is no need to break death damp for sanding. Instead, you can go for direct staining. Just clean the tabletop with some fabric, and stain it in detail.
How do You Strip and Refinish a Dining Room Table?
Proper stripping is required before the painting or varnishing surface of the dining table can refined. Use any stripping legman for this motive. First, spray the legman on the tabletop. let it sit there for the suggested time. After some time, the surface will become flexible. Next, remove it with a putty knife and clean it after opening it thoroughly. Do not let the wood surface grow.
After stripping, proceed to rearrange the table completely. Apply mineral spirits, grit the surface, sign it, and apply the finish. How to Refinish a Dining Room Table and you will bring back the new look of the dining room table.
It is an easy task to refurbish any dilapidated or old furniture in the house. Anyone can easily accomplish this task on their own without the help of professionals.This is not a challenging task.
How to refinish a dining room table requires some time and effort. Proper Protection and care make home furniture lasting and bright. Hopefully, the guide above will be helpful for you to refinish your dining table properly.